Including ZWave Node

Press the include button on your device...



Included node: {{ozw_node_id}}
{{ozw_node_desc}}

Excluding ZWave Node

Press the exclude button on your device...



Excluded node: {{ozw_node_id}}

Outside Temperature Sensor:
Command:





You can retreive old month records by running SBFSpot/SMASpot with commandline parameter -v -amXX,
where XX is the amount of months you would like to retreive, for example:
./SBFSpot -v -am12 , this will retreive up to 2 years from now.

This process can take a while, when pressing the above button, please wait until the dashboard is shown again!.

Nodes
NodeID Name Description Manufacturer ID Type Last Seen Enable Polling Status
Update    Delete Refresh


Configuration


User Codes

Code Value Action
Refresh

Please note, removing a code can take a while on battery operated devices.
To quickly force the hardware to remove the code (after pressing the remove button)
Use the tamper switch on the back to wake up the device.

Nodes
NodeID Name Sketch Name Version Childs Last Seen
Update    Delete Refresh


Childs
ChildID Type Name Values Ack Ack Timeout Last Seen
Update    Delete Refresh

 (ms)

Nodes
ID Name Mac Address
Update    Delete Clear

Add

Settings
 (Seconds)
 ()
Apply Settings

Nodes
ID Name IP Address Timeout
Update    Delete Clear

 (Seconds)
Add

Settings
 (Seconds)
 ()
Apply Settings

Nodes
ID Name IP Address Port
Update    Delete Clear

Add

Settings
 (Seconds)
 ()
Apply Settings

Nodes
ID Name IP Address Port
Update    Delete Clear

Add

Settings
 (Seconds)
 ()
Apply Settings
Auto Searching on:

Nodes
ID Name IP Address Type Uptime Hardware Firmware
Update    Delete    Update devices firmware Clear

Add

Settings
 (Seconds)
 ()
Apply Settings

Devices
ID Name Mac Address

Settings
 (Seconds)
 ()
Apply Settings
       
       
     
     
     
     
     
     



868.30MHz 868.30MHz FSK 868.35MHz 868.35MHz FSK 868.95MHz
         
     

You can only enable protocols for the same frequency!



Note: Any change will take effect after restarting Domoticz!


Hardware:


Meter 1:


Meter 2:


Meter 3:


Meter 4:


Meter 5:



Hardware:








Idx Name Enabled Type Address Port Data Timeout
Update    Delete




()
()




 ()
Make sure the correct pin status is read by introducing a bounce delay.
 ()
Maximum of one interrupt per pin allowed in this period (prevents interrupt storms).
 




Using CRC message validation prevents incorrect data from entering the Domoticz database.

 Seconds
This limits the amount of meter updates.



  Seconds



Change only to select another Toon when having multiple agreements



 (Seconds)

Leave the username empty and press the LINK button on the Philips Hue bridge. Then press the 'Register on Bridge' button.
Register on Bridge




Select the Topic('s) Domoticz will use to publish outgoing messages.
Flat - publish outgoing messagen on topic domoticz/out.
Hierarchical - publish outgoing messagen on topic domoticz/out/${floorplan name}/${plan name}.
Combined - Use both Flat and Hierarchical topic schemes.
None - disable outgoing messages.

Note that Hierarchical only reports sensor updates for sensors that are placed on a floorplan/plan.


Select the Topic(s) where Domoticz publish/receive messages.
MyMQTT (default) - domoticz/in/MyMQTT, domoticz/out/MyMQTT
Gateway Node Name - domoticz/in/GatewayNodeName, domoticz/out/GatewayNodeName (GatewayNodeName is specified in the Name field (above))

 (Seconds)
This sets the interval between status requests.
If you set this to less than 60 seconds you may be in violation of Honeywell's usage terms and have your account suspended!

When enabled this will automatically register and keep your zone names in sync with the Evohome controller.

When enabled this will show the next scheduled switch point when in Auto (FollowSchedule) mode.
(implies synchronize installation)
 
, , (keep at [0,0,0] if you only have one Evohome installation)
 

Add

Settings
 ()